| Items | Specification |
| Control mode | Control mode | V/F control | Sensorless in open loop | Close loop vector control |
| | Starting torque | 0.5Hz 150% | 0.5Hz 180% | 0.00Hz 180% |
| | Speed adjust range | 0: 50 | 1:100 | 1:1000 |
| | Speed stabilizing precision | ±1% | ±0.1% | ±0.02% |
| | Torque precision | NO | NO | ±5% |
| | Motor type | General induction motor permanent magnet synchronous motor (PMSM ) |
| Function design | Highest frequency | General vector control :320Hz V/f control: 3200Hz |
| | frequency resolution | Digital setting: 0.01Hz Analog setting:maximum×0.025% |
| | Carrier frequency | 0.5K～16KHz, the carrier frequency can be adjusted by temperature automatically |
| | Frequency reference setting method | Digital of Control panel, analog AI1, AI2, potentiometer of control panel, UP/DN control, communication, PLC pulse frequency |
| | Acceleration./deceleration characteristic | Linear curve and S curve accel. /decel. mode, range of time: 0.0 to 65000S. |
| | V/F curve | 3 mode: linear, multiple points, N Power |
| | V/F separation | 2 times separation: totally separation, half separation |
| | DC braking | DC braking frequency: 0.0 to 300Hz, DC braking current: 0.0% to 100% |
| | Braking unit | Standard built in for up to 4T22G (22kw), optional built it for 4T30G～4T110G (30kw to 110kw), external built for above 4T160kw . |
| | Jog function | Job frequency range: 0.0 to 50.0Hz, the acceleration and deceleration time of Jog |
| | Configured PID function | Easy to perform pressure, flow, temperature close loop control. |
| | PLC multiple speed | To achieve 16 segment speed running through built in PLC or terminal control |
| | Common Dc bus | Multiple drives use one DC bus for energy balance. |
| | Auto voltage regulation (AVR) | Enable to keep output voltage constant when grid fluctuation |
| | Over load tolerance capability | G type model: 150% rated current for 60s, 180% rated current for 3s, P type Model: 120% rated current for 60s, 150% rated current for 3s. |
| | Stall protection control when over current, over voltage | Carry out limiting automation for running current, voltage to prevent over current, over voltage frequently |
| | Rapid current limit function | Minimize the IGBT module broken to protect the AC Drive, maximum reduce the over current fault. |
| | Torque limit and torque control | "Excavator" characteristics , torque limit automatically during motor running. Torque control is available in close loop vector control mode. |
| Features | Friendly interface | Display “Hello” when power on. |
| | Multiple function key JOG button | It can set for Forward Jog, reverse Jog, forward/reverse switch |
| | Timing control function | A total running time and total running time calculating |
| | 2 group motor parameters | To achieve two motor switchover freely, control mode is selectable |
| | Motor over heat protection | Accepting motor temperature sensor signal input via AI1 terminals. |
| | Multiple kinds encoder * | Compatible collector PG, differential PG, and rotary transformer Encoder( resolver). |
| | Command source | Control panel, control terminals, series communication, switch freely. |
| | Frequency source | Digital setting, analog current/voltage, pulse setting, serial communication, main and auxiliary combination. |
| | Protection function | Short circuit detect when power on, input/output phase loss, over voltage, over current, under voltage, over heat, over load protection. |
| Environment | Application site | Indoor, free of exposure to sunlight, no dusty, no corrosive, no inflammable gas, no oil and water vapor, and water dipping |
| | Altitude | Lower 1000m |
| | Environment temperature | -10℃～+40℃, power derated for 40～50℃, rated current derated 1% for 1℃ increasing. |
| | humidity | Less than 95%, no water condense. |
| | storage | -40～+70℃ |
| | IP degree | IP20 (IP54 is avaliable) |
